TOKO ROBOT - Pololu MQ Gas Sensor Carrier

Produk Item # : 1479
Harga : Rp. 34.875
Stok : 2

This carrier board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, power and analog voltage output—that are broken out with a 0.1" spacing, making the board compatible with 0.1" headers and standard breadboards and perfboards. This board has two mounting holes and provides convenient pads for mounting the gas sensor’s required sensitivity-setting resistor.

 

This breakout board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, +5V VCC, and an analog voltage output—that are broken out with a 0.1" spacing, making the board compatible with 0.1" headers and standard breadboards and perfboards. This board has two mounting holes and provides convenient pads for mounting the gas sensor’s required sensitivity-setting resistor (referred to as RL in the sensor datasheet). All of the board’s traces are on the same side of the PCB, making it easy to see how the pads are connected.

The two mounting holes are intended to be used with #2 screws (not included).

Note that we also offer an alternate gas sensor breakout board that is more compact, with a diameter equal to that of the smaller gas sensor and the broken-out pins beneath the sensor.


Connections

Connect VCC to 5 V, GND to ground, and OUT to an analog-to-digital converter (ADC). The board has two pairs through-hole pins for the required (but not included) sensitivity-selecting resistor RL, providing two mounting options—horizontal or vertical—between GND and OUT as shown in the pictures below. The resistance of RL should be calculated using the datasheet for your particular gas sensor.

The MQ gas sensors have light to no polarity, so the gas sensor will work with the board all four ways it fits into the 6 pins (there are two possible orientations on each side of the board).

Pololu MQ gas sensor carrier with sensitivity-setting resistor soldered in the horizontal orientation.
Pololu MQ gas sensor carrier with sensitivity-setting resistor soldered in the vertical orientation.

The picture to the right above shows a board with a 3×1 0.1" right-angle male header soldered to it, which allows a standard servo cable to be used to connect the board to your project.

Note: This product consists of the PCB by itself; it does not include a gas sensor, sensitivity resistor, header pins, or any additional hardware.


People often buy this product together with:

Alcohol Gas Sensor MQ-3 Alcohol Gas Sensor MQ-3
Flammable Gas & Smoke Sensor MQ-2 Flammable Gas & Smoke Sensor MQ-2

 

Carbon Monoxide Gas Sensor MQ-7 Carbon Monoxide Gas Sensor MQ-7

 


Tag Toko Robot:

Toko robot Robot edukasi
Edukasi robot Lomba robot
Robot lomba Kontes robot
Robot kontes Kompetisi robot
Robot kompetisi Robot kit
Robot kit untuk edukasi Robot Indonesia
Maze solving robot Jual komponen robot
Robot Maze solving Jual komponen robot murah
Line tracing robot Jual controller robot
Robot line tracing Jual kontroler robot
Line tracer robot Jual sensor robot
Robot Line tracer Jual aktuator robot
Line following robot Jual motor robot
Obstacle robot Menjual KIT Robotik
Robot Obstacle Jual komponen dan kit robot
Robot untuk lomba Jual Spare Part Robot
Robot untuk kontes Jual robot Pololu
Robot untuk kompetisi Jual robot KAIROBOT
Olimpiade robot Jual Line Tracer non Programming
Robot Olimpiade BLACK LINE PRO Murah
Jual robot Jual Robot Maze Solving
Jual robot kit Jual Robot Line Follower
Jual robot kit untuk pendidikan Jual Robot Line Tracer
Jual robot kit untuk edukasi Jual Robot Line Tracing
Jual robot untuk lomba Jual robot untuk kontes
Robot kit untuk anak TK Jual robot untuk kompetisi
Jual komponen dan kit robot Robot untuk anak TK
Pusat penjualan komponen dan alat alat robotika Robot untuk pendidikan anak TK
Robot Line following

Jual berbagai sensor, motor,

kontroler, aktuator robot

 

Dimensions

Size: 0.7 x 0.95"

resource